Mytee 1001DX Manuel d'utilisateur télécharger pdf (Page 28)

17. The voltage and frequency indicated on the name plate must corre-

spond to the wall receptacle supply voltage.

18. When cleaning and servicing the machine, local or national regulations

may apply to the safe disposal of liquids which may contain: chemicals,

grease, oil, acid, alkalines, or other dangerous liquids.

19. Do not leave operating unattended.

Preparation

1. Remove furniture and other items from the area you are going to clean.

2. Vacuum carpet and upholstery, and remove debris.

3. Protect cabinets, walls and painted surfaces with drop cloths or plastic.

4. Inspect power cords for damages.

Operating Instructions

1. Fill the solution tank.

2. Attach one end of a solution hose to a wand or other tool, the other end

to the Speedster’s® front quick disconnect.

3. Attach one end of a vacuum hose to the tool, the other end to the

Speedster’s® Cuff-Lynx™ vacuum hose port.

4. Plug in power cords.

• 1000DX and 1000DX-200 models – Plug single cord into single, 20A

grounded wall outlet.

• 1001DX, 1001DX-200 models – Using two separate circuits/breakers,

plug the left power cord into 20A grounded wall outlet to turn on Vac 2 and

Heater 2. Plug the right power cord into separate 20A grounded wall outlet

to turn on Vac 1, Heater 1 and Pump.

• 1003DX models – Using two separate circuits/breakers, plug the left

power cord into 20A grounded wall outlet to turn on Vac 2 and Heater 2.

Plug the right power cord into separate 20A grounded wall outlet to turn on

Vac 1, Heater 1 and Pump.

• 1005DX models – Using two separate circuits/breakers, plug the left

power cord into 20A grounded wall outlet to turn on Vac 2. Plug the right

power cord into separate 20A grounded wall outlet to turn on Vac 1 and

Pump.

The amber light indicator on the switch plate will illuminate brightly when

cords are plugged into two separate circuits. Do not use extension cords

longer than 50 feet.

5. Turn on switches.

• 1000DX, 1000DX-200, 1005DX models – Turn on Vac 1, Vac 2 and

Pump switches.

• 1001DX, 1001DX-200 and 1003DX – Turn on Vac 1, Vac 2 and Pump

switches. Turn on Heater switch if heat is being used. Wait several

minutes for water to heat. Heater switch has three positions: Off (middle);

1,000 watts using one heater (left); and 2,000 watts using two heaters

(right). Red lights on panel display indicate watts selected: one light =

1,000 watts; two lights = 2,000 watts; no lights = heaters are off.

6. 1003DX and 1005DX models – Prime Valve and Pressure Regulator

are located on the lower front of the extractor. To prime the pump, turn the

valve to the Prime position for 30 seconds, then turn horizontally to the

Run position. Turn the Pressure Regulator to the left to decrease the water

pressure. Turn to the right to increase water pressure. Level will be visible

on the pressure gauge. Monitor while adjusting, using Pressure Gauge on

Switch Panel.

7. Begin cleaning. Make two dry passes to every wet pass. Work away

from cords to avoid damage. To clean heavily soiled areas, repeat clean-

ing from a different direction.

8. Use a foam control solution in the recovery tank to prevent motor dam-

age and check for foam build-up in recovery and solution tanks.

9. Empty the recovery tank as needed when the internal ball oat auto-

matically shuts off the vacuum. Attach the 45˚ drain elbow to the drain

spout in back. Lift up the dump valve and empty tank.

10. To relieve water pressure from the solution hose before disconnecting

it, squeeze the tool’s trigger ve seconds after turning the power switches

off.

11. Once machine is off, unplug power cords. Remove solution and

vacuum hoses. Empty the recovery tank by attaching the 45˚ drain elbow

to the drain spout in back. Lift up the dump valve and empty tank.

12. 1003DX and 1005DX models – Water remaining in the solution tank

can be emptied by turning the Prime Valve to the right to move water into

the recovery tank. Empty recovery tank.

After Use

1. Before storing machine, drain, rinse and dry tanks and vacuum hose of

water and solution.

2. Store in a dry are in the upright position.

3. Open recover tank cover to promote air circulation.

4. Store indoors in a dry area. If storing in freezing temperatures, make

sure the machine and solution system are completely drained and dry.

Maintenance Schedule

Latches are located in back to open tank for internal maintenance. To

keep machine in good working condition, follow machine’s daily and

weekly maintenance procedures. Check valves and relief valves should be

replaced annually.

Maintenance item Daily Once a week

Clean and inspect tanks.

Clean and inspect hoses.

Check and clean internal lters by twisting

off, rinsing with clean water and replacing.

Check power supply cable.

Clean machine with all-purpose cleaner

and cloth.

Check spray nozzles.

Flush solution system with Mytee

System

Maintainer.

Remove and oat shut-off screen from

tank and clean. Simply pull off.

Inspect vacuum hoses for holes and loose

cuffs.

Inspect spray pattern for clogging. If

clogged, remove spray tips and soak them

in a recommended liquid neutralizer for

up to six hours. To remove spray tip, twist

spray tip body counter-clockwise.

Lubricate wheels with water resistant oil.

Inspect machine for water leaks and loose

hardware.

Trouble Shooting

There is no power.

1. Plug machine in proper outlet.

2. If using two cords, make sure each is plugged into a separate circuit.

3. Check circuit breaker. Reset circuit breaker, other items should not run

on the same circuit as the machine. Outlet must be a 20-amp circuit.

Pump does not work properly

1. Snap quick disconnects rmly together.

2. Check solution tank; may be empty.

3. Jets clogged, remove jet and ush clean.

4. Filters clogged, remove lters and rinse clean with water.

5. Heater is blocked; ush out with Mytee’s® System Maintainer.

6. If brass check valve is stuck, replace valve.

7. Check pump wire. May need to reconnect wire.

8. Switch plate may need to be replaced.

9. If pump motor brushes are worn, replace pump.

1001DX, 1001DX-200 or 1003DX heater does not work properly

1. If sensor mounted on the heater has popped, reset sensor by pushing

in button.

2. Heating element may need to be replaced.

Vacuum motor does not work properly

1. Check that hose is tightly connected.

2. Close drain hose valve completely.

3. Secure the vacuum tank tightly.

4. If ball oat is shut off, empty vacuum tank of all wastewater.

5. Make sure ball oat is rmly installed on the elbow.

6. If water is coming out of the vacuum motor, use a low foaming

detergent.

7. Clean upholstery tool or oor wand jets.

GENERAL INFORMATION

1 2 ... 23 24 25 26 27 28 29 30 31 32

Commentaires sur ces manuels

Pas de commentaire

Mytee 1001DX Manuel d'utilisateur Page 28

Commentaires sur ces manuels

Produits connexes et manuels pour Machine à plancher Mytee 1001DX